Nice chatting with you today, beautiful car you have there, if I had the room in the garage I would purchase it and have 1 of each. Good luck with your sale
Sent from my KB2005 using Tapatalk
Loading...
|
Type: Posts; User: USAWIT2; Keyword(s):
Nice chatting with you today, beautiful car you have there, if I had the room in the garage I would purchase it and have 1 of each. Good luck with your sale
Sent from my KB2005 using Tapatalk
Regret selling my old notch, but in the process of building a new one, currently out for...
Yes you can have anything shipped.
Sent from my KB2005 using Tapatalk
You could always use crossborderpickups.ca, I've used it a couple of times, way cheaper then shipping direct.
Sent from my KB2005 using Tapatalk
Try Jeff @ Mustang Specialteaz, he's parting out a few cars of that year
Sent from my KB2005 using Tapatalk
Yep, plan is to be there, hopefully no rain
Sent from my KB2005 using Tapatalk
Planning on it, hopefully the weather stays as good as they say it will be
Sent from my KB2005 using Tapatalk
As the title says, looking for a clean Gen2 Coyote and 6r80 2wd trans, lower the kms the better, F150 or mustang will consider either.
Thanks
Sent from my KB2005 using Tapatalk
It seem too, didn't really use it that much being a vert and all.
I assume they jumped the switch because it was bad or the compressor was or the compressor went bad because they jumped the switch
...
I had the system apart to do the heater core, I had it recharged and in the process realized the low and high side pressures weren't where they were suppose to be.
I also found that the pressure...
When it is warped is that leak internal? My system doesn't have any leaks, just doesn't seem to build much pressure.
Unit spins pretty freely by hand
I'll check Rock Auto again, didn't see a seal...
Might be a long shot but I'm looking for a good used AC compressor for my 91.
Or maybe someone might know where to get a seal kit so I can rebuild the one I...
Well figured out my clunk, my mistake when assembling the front diff brace. I tightened the two bolts that hold the LCA/diff brace before I tightened the 2 that hold the diff to the brace. They...
When I take it out this weekend I'll have to see if it gets worse/louder the longer I drive it.
If it is just the floor is there a fix for it or is it something you have to live with?
Sent from...
So since installing the FTBR bushing kit I've developed a clunk in the rearend.
It was probably there all the time but masked by the OEM bushings.
Noise always seems to come from the PS rear. ...
Same one that was forsale on Kijiji a couple weeks ago out London way?
Sent from my KB2005 using Tapatalk
Following the housing market by the looks of it
Sent from my KB2005 using Tapatalk
I wonder if there will be a lease option for the Mach E? or maybe Ford doesn't want them back after a couple years.
Sent from my KB2005 using Tapatalk
Had the Cobra out today, had an appt to get the alignment done.
91vert was out for a little test spin on Thursday
You could try aluminum brightener, I got some from NAPA, just make sure you rinse well
I ran 10's on my old notch, depending on the tire size the inner fenders might need some massaging.
Rear end does move side to side during cornering or articulation even with a panhard bar so if...
You might want to consider 245/40/17 for the front, the 45's always look taller then 275/40/17
Also checkout PMCtire.com they usually have good pricing
Wasn't as much of a PITA as I thought it was going to be.
The lift came in handy, don't think I would have wanted to do it on jack stands
Must be it, or the person's on crack
I got the two angles matching as per the FTBR instructions, going to have it double checked when it goes for an alignment in the spring