The red GT Richard? If it was, I've still got it.
Loading...
|
Type: Posts; User: TC86GT; Keyword(s):
The red GT Richard? If it was, I've still got it.
I have a blow through on my Turbocharged 86GT. No enclosure, I have heard they can be problematic but I don't have any experience directly. I'm just using a CSU 750cfm blow through specific carb. ...
If you have a CSU carb set up as a blow through, you don't need an enclosure. That usually reserved for unmodded carbs and can be temperamental from what I understand.
Typically on a carb set up...
Sent you a PM.
I would think that in normal driving out of boost (in vacuum) that fuel economy wouldn't be too different if the tunes were equally decent. Only possible difference would be the parasitic drag of...
Garden hose with hot water flowing over large areas works extremely well on large areas of vinyl, typically will take the adhesive with it cleanly. The rubber eraser wheels work well but large...
You'll pretty much need to connect to a manifold vaccum port that's in the intake after the compressor (below). It will see both vacuum and boost pressure this way. I think they are trying to...
Stick car, buy the biggest, strongest axles you can afford. Automatic car with a soft leave, you can typically push the limits a bit more. I've seen 13 second stick cars snap stock axles like a...
I have a set on my wife's Fusion. (235 50 17) Been on just about 15,000km now, no real noticeable wear/weird wear patterns at all. Seems to be a good all around tire. Rides nice, quiet, no...
https://www.diyautotune.com/shop/mspro-efi-ems/mspnp-gen2/mspnp-gen2-ecus/
That's where I got mine from a few years back. www.efianalytics.com has some info on the Tunerstudio software to look at...
I'd go the other route and up-size the blower pulley. Reducing the belt contact area on the crank pulley and a small blower pulley can get into potential belt slippage territory. Keep the stock...
MS3 is a great choice, not much it can't do. I hate wiring which was one of my reasons for the plug and play version of the MS2. I'm sure I could have built my own and got it functioning, but...
Similar to what I did when I added the turbo. Tossed the Mass air and bought a Megasquirt 2 plug and play. Running it in speed density, and just entered my 60lb injectors into the software and let...
Good point worth mentioning, on a radial tire, if they spin and get into tire shake...that's hard on parts. Axles, diffs, wheel studs...pretty much the entire driveline. A bias ply spins, that's...
Not enough power or gear to warrant a 28" tire, stay with the 26" tire, it will work best at this point.
Next time out with the BFG's, drop the pressures low and cook them in the burnout. With my...
Going by what be posted he's running 109mph with the blower from his original post. Just using the info I was given to plug in the calculators. Plugging in a 115mph trap speed without factoring in...
From the online calculators (http://www.wallaceracing.com/Calculators.htm) I'm seeing just under 5000rpm the way it sits now. 3.55 gear, approximately 27" tire if it's near stock size and 109mph...
28" tire is a lot of tire. You have to accelerate that mass and the height and growth will kill your effective overall gearing. I'd stay with a 26" tire, which when it grows at speed will be very...
Full slick, MT or Hoosier 26x10 on an 8-10" rim.
DOT slick, Hoosier Quick Time Pro or MT ET Street bias ply in 26x11.50.
Plenty of tire that will take you well beyond your current level. ...
First off don't fear the gear. To me going from a 3.55 to a 3.73 wouldn't be worth the effort. Step up to a 4.10, especially on a bigger/heavier '05 GT.
Tires, 15" set-up with a sticky slick...
My old '05 GT auto had 4.30's, C&L Racer intake tube and tune as well as secondary runner delete plates. It ran 13.1 @ 104 on too tall (28" tall) street tires. The fellow I sold it too put on some...
From what I have gathered through the years, the Spintech mufflers sound awesome but are some of the worst flowing mufflers on the market. Removing them, in just about all the cases I've read, have...
Pump gas 408 on a conservative 150 shot...why I rolled out on the hit I'll never know.
https://www.youtube.com/watch?v=0GxqtET0SfY
Junkyard 351's final ride, every colour smoke possible and...
I'll round up some footage...
LOL! Glen, the motor was yanked from a '72 Torino, cut-off wheel clearanced pistons and bolted my top end on. Pure junkyard and it ran pretty well. Didn't hit the 9's but got close, we figured it...