Loading...
Remove Text Formatting

Search:

Type: Posts; User: ZR; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.43 seconds.

  1. Also good idea to check pivot at the clutch pedal...

    Also good idea to check pivot at the clutch pedal for excessive play eating up your adjustment. Very common for them to get loose / break n fall off on higher mileage S197's....
  2. If it got a bit better, needs more bleeding....

    If it got a bit better, needs more bleeding.
    Flat surface, engine off, steady pump the pedal up and down (not too fast)
    We've seen the odd one take 300 or more cycles to fully purge all of the air....
  3. Did you install a new slave / release bearing at...

    Did you install a new slave / release bearing at the same time? If so, what make?
    Did they confirm installed height of the new flywheel matches the original?
    Most likely air still in the master /...
  4. Replies
    1,381
    Views
    234,656

    ^ For Covid pricing, it's a great deal.

    ^ For Covid pricing, it's a great deal.
  5. Check out MustangSpecialteez

    Check out MustangSpecialteez
  6. You looking for a 7.5 or 8.8 diff?

    You looking for a 7.5 or 8.8 diff?
  7. Replies
    1
    Views
    113

    Nice clean cars are hard to find.

    Nice clean cars are hard to find.
  8. Replies
    29
    Views
    785

    Drove a Venom on the racetrack, surprised how...

    Drove a Venom on the racetrack, surprised how forgiving it was to drive. Combo of excellent chassis and suspension combined with stellar electronics (trac control / ABS / etc) helps keep things in...
  9. Replies
    29
    Views
    785

    Man you gotta be excited.

    Man you gotta be excited.
  10. Thread: Header Clearance

    by ZR
    Replies
    11
    Views
    201

    I know it'll hurt taking a hammer to new headers...

    I know it'll hurt taking a hammer to new headers but a dent won't make an ounce of perf difference. Can make a pretty clean job of it by marking, removing, lay one hammer against it and strike with...
  11. Replies
    29
    Views
    785

    ^ Sweet purchase, how you enjoying it? A h/p car...

    ^ Sweet purchase, how you enjoying it?
    A h/p car with an auto was never so much as a blip on my radar until I drove one of Blackstocks cars, amazing how well it works.
  12. Replies
    29
    Views
    785

    ^ One hell of a car.

    ^ One hell of a car.
  13. Thread: Header Clearance

    by ZR
    Replies
    11
    Views
    201

    Motor mounts a little sagged can cause it?...

    Motor mounts a little sagged can cause it?
    Sometimes a shim / washer or two under the stud where it goes through the K member will give you enough clearance (or between block and motor mount). Also...
  14. Thread: Broken dipstick!!

    by ZR
    Replies
    7
    Views
    119

    Used a screw to remove more than once.

    Used a screw to remove more than once.
  15. Thread: Broken dipstick!!

    by ZR
    Replies
    7
    Views
    119

    Lucky you got the lower section out, can...

    Lucky you got the lower section out, can sometimes require pulling the pan to tap out from below.
  16. Car was brought back to life.

    Car was brought back to life.
  17. Replies
    20
    Views
    388

    I was good sans wipers. :) Just gotta drive...

    I was good sans wipers. :)
    Just gotta drive faster, thought I showed you dat one (outlet mall drive).
  18. Replies
    10
    Views
    326

    Nice purchase, more pics n details please.

    Nice purchase, more pics n details please.
  19. Replies
    20
    Views
    388

    While I appreciate mine when clean, don't melt in...

    While I appreciate mine when clean, don't melt in the rain.
  20. Thread: Alternator Issue

    by ZR
    Replies
    10
    Views
    210

    When installing new alt, make sure mounting boss...

    When installing new alt, make sure mounting boss to the engine is spotlessly clean. First time even I've seen it be an issue was on Ross's car last summer. Off n on alt not charging, alt overheating,...
  21. Thread: Alternator Issue

    by ZR
    Replies
    10
    Views
    210

    O'drive crank pulley or stock? Has battery gone...

    O'drive crank pulley or stock?
    Has battery gone flat / car boosted?
    Battery front or trunk?
  22. Replies
    35
    Views
    640

    Exactly.

    Exactly.
  23. Replies
    35
    Views
    640

    Good thought.

    Good thought.
  24. Thread: VVT VALVE GASKETS

    by ZR
    Replies
    6
    Views
    112

    Have a new set of Ford Racing 3v covers sitting...

    Have a new set of Ford Racing 3v covers sitting here under my desk. Seal looks to be installed from the outside, may be able to remove with a small drilled hole, screw and a puller but can't be sure...
  25. Replies
    35
    Views
    640

    I've contemplated one several times but can't...

    I've contemplated one several times but can't bring myself to have one on the interior in case of a big impact and it breaks loose.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

SiteUptime Web Site Monitoring Service