I'm looking for a known good 'steel gear' distributor for my '90 5.0. I tried a 'new' Cardone unit but the gear was not meshing correctly. Tried a 'reman' Cardone and no spark...
I'm in Waterloo....
Loading...
|
Type: Posts; User: hemi_fan; Keyword(s):
I'm looking for a known good 'steel gear' distributor for my '90 5.0. I tried a 'new' Cardone unit but the gear was not meshing correctly. Tried a 'reman' Cardone and no spark...
I'm in Waterloo....
Hamilton is not bad. I'm there every couple of weeks anyway. I tried a couple of local KW body shops but they either seem to want to focus on insurance repair or seemed shady (I.e. would not give a...
Does anyone have a recommendation on someone who could finish and paint my foxbody?
The car is assembled enough to drive but I would want them to install and mold my 2" rear arch flares, then full...
Thanks guys. Its different from the fuel filter clips. Canadian Tire had the fuel filter type but they don't work. I'll try the dealer and Mustang Specialteez!
21767
Anyone know where I can get a retaining clip to hold the line to the sending unit? It is a C-Clip for the 5/16 sending line.
Seems like a good price for a great colour combo. Clearly enthusiast owned.
2019 Ford Mustang GT Premium,...
https://bringatrailer.com/listing/1989-ford-mustang-gt-5-0-convertible-10/
Cherry 89 5-spd 5.0 GT Vert
Interesting take. I have seen a lot of SC Coyote cars making 700+ whp online recently too. His last comment about the GT being better bang for the buck was interesting. I've been seeing used 19/20...
How does the '11/'12 GT500 5.4 compare to the '13/'14 5.8 when it comes to mods? Obviously stock vs. stock there is a huge difference but does it matter much once you start talking pulley/tune or...
Yep, used to be at 990 Isabelle. Great neighbourhood, I enjoyed Windsor. But got a great opportunity to move closer to my family and had a little one on the way last year.
Yessir. Black Diamond 6SPD sedan. Loved that car but homes in Waterloo are much more expensive than Windsor :(
Hi Brad, excited to be back :) The fox has barely been driven the last ~7 years so I tore into it last spring. The mod list will look similar to your sig ;) except my car is not that clean so I am...
I had QTP cut-outs with the remote on my '11 CTS-V. Worked great, never had an issue. Sounded like the world was ending when open.
https://www.youtube.com/watch?v=zC-luJB7VTg
Pat's price is ~$30 more vs. Shaftmasters. Benefit is I can take my yoke and flange and they can balance the assembly.
3.5" aluminum, 1330 U-joints, 43.75" center-to-center, re-use yoke and flange...
They built the shaft for my Volvo LS swap. I agree, they are awesome. Their name had escaped me, thanks for the reminder.
Ah I remember those guys. Worked in Wixom a few years but never bought anything from them.
Just found out 03/04 terminator driveshaft are 0.8" shorter than GT. Not quite as short as I'd like but...
What is D&D? I'll check out Pat's.
Found some sources online but all in the US. There are cheap 3" custom shafts that I think would work but are a downgrade strength wise. A couple of shops doing...
Has been a long time. Moved to Waterloo from Windsor last summer and decided to get the old fox road course ready :) Hopefully I can get it back on the road this summer. Lots of work to do though.
Any recommendations on where to get a custom aluminum driveshaft for my 90 GT? I installed the MM x-member and want to take advantage of its ability to set the engine 1" back. Stock DS is basically...