Loading...
Remove Text Formatting

Likes Likes:  219
Page 2 of 2 FirstFirst 12
Results 11 to 19 of 19

Thread: The 03 Cobra Zinc Build

  1. #11
    Dech Boy Zippy's Avatar
    Join Date
    Mar 2014
    Location
    Toronto
    Posts
    4,991
    Clutch in and set up properly.
    Bell Housing cleaned up and painted.
    Wires and O2 sensors tied up against the trans so they do not get burnt on the header.
    K member bolted up to the motor after being squared into the car.
    Valve covers pulled off and re-gasketed. Redid all the bolt grommets aswell as the plug hole gaskets.
    At this time we also pulled off the headers and re-gasketed them as well.
    When they were installed by another shop... used aftermarket gaskets and were already leaking. Only use MLS style gaskets on a Cobra for the manifolds/headers!
    20201204_142120.jpg

    98 GT - Bright Atlantic Blue 'Dech'

  2. #12
    Dech Boy Zippy's Avatar
    Join Date
    Mar 2014
    Location
    Toronto
    Posts
    4,991
    It quickly came together... Here's what the final pics of under the hood look like.
    Maximum CC plates in, Maximum Strut tower brace... everything cleaned up !
    Came out freaking sweeeeeeeeet.
    Will have some more pics in the next week or so.

    20201222_185519.jpg
    20201222_185529.jpg
    20201222_185524.jpg

    98 GT - Bright Atlantic Blue 'Dech'

  3. #13
    Dech Boy Zippy's Avatar
    Join Date
    Mar 2014
    Location
    Toronto
    Posts
    4,991
    Brembo Brake kit mounted
    Stainless steel lines
    New rotors
    EBC red pads front and rear
    New ATE Brake Fluid
    20210601_104117.jpg
    20210601_104111.jpg
    20210601_104122.jpg

    98 GT - Bright Atlantic Blue 'Dech'

  4. #14
    Dech Boy Zippy's Avatar
    Join Date
    Mar 2014
    Location
    Toronto
    Posts
    4,991
    Mike's Cobra is finally all complete
    (minus break in on the clutch and tune)
    New 17x9 and 17x10 CCW wheels wrapped in Nitto tires on the car
    Gauges installed
    Volt, Boost & a Shift light
    Cluster repaired (didn't have any lights on at night)
    New Alternator
    - Was recently replaced by another shop, they installed the wrong regulator on it

    Looks pretty sporty with the top down !
    This is definetely the tightest feeling vert in a new edge I've ever been in
    All of the Maximum motorsport goodies and the amazing Koni DA shocks in the front with the upgraded bilsteins in the back...
    It rides & handles like a dream.
    Dyno in a few weeks... should make just under or just over 600 at the tire


    20210610_161812.jpg
    20210610_161756.jpg
    IMG_20210610_163058_455.jpg
    20210610_161749.jpg

    98 GT - Bright Atlantic Blue 'Dech'

  5. #15
    Dech Boy Zippy's Avatar
    Join Date
    Mar 2014
    Location
    Toronto
    Posts
    4,991
    Update on the Zinc build.

    Customer put about 1,000kms on the car before hitting the dyno.
    Did that to properly break in the clutch and make sure everything was good to go...
    Bad news unfortunately on the dyno...
    Car made 2 pulls on the dyno that went smooth as silk, as the tuner was loading in the revision for pull #3, on start up, the car was on 7cylinders.
    Long story short, the car dropped a valve seat. (not the tuners fault, or anyone's for that matter)
    Major blow
    The motor has long since been pulled from the car and over to our machine shop (Beatty&Woods).

    Mike, the owner of the car, has decided now is the time to do cams and some other upgrades inside the motor while the heads are being fixed.
    Going with Crower stage 2 cams, upgrade GT500 rockers and TFS lash adjusters.
    The good news in all of this is...
    1. The tuner, DCT, realized what was happening and didn't continue with the dyno tuning
    2. The valve did not hit the piston and cause anymore damage to the bottom end
    3. No damage to the heads
    4. the car was already at 560ish on the second pull with very very very low timing in it.
    Obviously a big blow to everyone involved as the car was pretty much complete. We will be getting the motor back sometime in the next couple of months and will have the car reassembled for spring time.
    This Cobra is going to be a ripper once completed. With the new cams and upping the boost, Mike should be in the 640-650 range once we get it back together.

    Here is a photo of the driver side valve cover. If you can zoom in, the rocker arm is off.
    20210809_150157.jpg
    20210811_135513.jpg

    98 GT - Bright Atlantic Blue 'Dech'

  6. #16
    Dech Boy Zippy's Avatar
    Join Date
    Mar 2014
    Location
    Toronto
    Posts
    4,991
    Little update on the Cobra build
    We took this apart way back in the fall... and the machine shop still doesn't have the parts they need to put the motor together.
    I believe we are waiting for rings? for the pistons before they can start getting it back together.
    It's really unbelievable that parts supply issues are getting even worse then what they were a year ago.
    3 or 4years ago, this would be a 5 or 6week rebuild and it would be done. Now we are talking 5-6months+.
    Insane.

    Hopefully have this back soon and get Mike up on his feet and back to enjoying his car.

    98 GT - Bright Atlantic Blue 'Dech'

  7. #17
    Dech Boy Zippy's Avatar
    Join Date
    Mar 2014
    Location
    Toronto
    Posts
    4,991
    Yes yes I know... I've been bad about updates... but here is one!

    We have long since got Mike his car back with the new motor installed with the cams.
    Life got in the way for Mike and he hadn't gotten around to put any kms on it! Well this spring he finally got the break in miles done on the motor.
    Here are accouple of photo's of it in the shop about 3 or so weeks ago.
    Side note, this might be the tightest Vert cobra we get the pleasure of working on. The subframe connectors, full tilt boogie, K members, coilovers... makes it ride and drive incredibly well. We often forget that these cars are 20+ years old at this point! Where does the time go?

    Fast forward to today... DYNO DAY!

    So to remind everyone...
    2.3 Whipple
    BBK headers with a CATTED X pipe
    JLT Cold Air
    Magnaflow cat back
    Crower stage 2 cams with TFS lash adjusters & GT 500 roller rockers
    Lethal budget return fuel system
    Motor built by Beatty & Woods
    Tuned by DCT

    The car put down a wicked 618 @ 14lbs of boost in todays heat. IMPRESSIVE!
    Mike is going to be floored when he hits it for the first time.
    It has been a super long journey with the car... but we saw it through to the end.
    Another badass Cobra created.
    20230706_132953.jpg
    20230706_133027.jpg

    98 GT - Bright Atlantic Blue 'Dech'

  8. #18
    Dech Boy Zippy's Avatar
    Join Date
    Mar 2014
    Location
    Toronto
    Posts
    4,991
    Video of dyno session in the next couple of days!

    98 GT - Bright Atlantic Blue 'Dech'

  9. #19
    Dech Boy Zippy's Avatar
    Join Date
    Mar 2014
    Location
    Toronto
    Posts
    4,991
    Here is a link to DCT's facebook page

    Video of the car putting the power down

    https://www.facebook.com/DiagoCustom...84703190828697

    98 GT - Bright Atlantic Blue 'Dech'

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

SiteUptime Web Site Monitoring Service