PDA

View Full Version : 2015 Mustang GT stock spoiler (more of a winglet) removal



Armen
08-28-2015, 05:00 PM
The purpose of this would be to install a new rear spoiler. If you just want to remove the rear spoiler for a delete look, you're gonna have some holes to cover so you might want to just look into replacing the entire decklid with one that doesn't have a factory spoiler.

Whichever aftermarket spoiler you choose, make sure it will cover the holes left in the decklid after removing the stock spoiler.

Pop the trunk and you'll clearly see two access holes in the far left and far right side in the underside of the decklid, directly underneath the spoiler. Using an extended 10mm socket, remove the nut on either side. Be careful not to drop the nuts in between the outer and inner decklid sections. To assist in this, you may want to close the decklid slightly when the nuts are almost off the spoiler bolts so they 'set' into the socket with good old gravity.

There are two more nuts located more towards inner spoiler section. You'll need to remove the trunk latch cover by gently pulling and moving it from side to side until it comes off.

Next, unscrew the rubber stops in the 'carpet' decklid panel interior backing. There's one on the left and one on the right. There are several carpet clips that secure this carpet piece to the inner decklid section but you only have to remove the two near the latch. After removing these two clips, pull down the carpet (and over the latch) until you see the the centre access hole and nuts for the inner section of the spoiler. To remove these you'll need the same 10mm socket and an extension. The access hole for both these nuts is much larger so one can actually place a finger over the nut in the socket as it comes loose - again so as not to take a chance at dropping the nut in between the exterior and interior decklid section.

Once these four nuts are removed, get a plastic edging tool (putty knife, scraper, etc). You'll need this to separate the the adhesive that bonds the spoiler to the decklid. I taped up the plastic edging tool with painters tape just for extra protection against marring the paint. You'll want to make sure the car has been sitting in the warm sun so the adhesive is more pliable. Alternatively you could use a blow dryer to warm up the adhesive to make it easier to separate.

Gently pull up on one side of the spoiler just enough so as to allow pushing the edging tool in between the decklid and the spoiler. Gently work the edging tool forward, in a side to side motion. Work your way around the entire spoiler, being careful to 'go around' the spoiler bolts that you removed the nuts from. As the adhesive gives way, you'll be able to gently pull up the spoiler and separate it from the deck lid. This shouldn't require a lot of force. If it does, you've likely missed separating some adhesive, so go back with your edging tool and work your way around again, checking for any missed sections.

After the spoiler is removed, use a gunk cleaner and rag to remove the leftover adhesive residue on the decklid.

You're done and now the decklid is ready for your new spoiler.

Armen
08-29-2015, 09:57 AM
http://i243.photobucket.com/albums/ff276/armenk2000/Misc/spoiler6_zpsmhav15kl.jpg

http://i243.photobucket.com/albums/ff276/armenk2000/Misc/spoiler7_zpskwbeqpfo.jpg

http://i243.photobucket.com/albums/ff276/armenk2000/Misc/spoiler5_zpszyapgjut.jpg

http://i243.photobucket.com/albums/ff276/armenk2000/Misc/spoiler3_zpsrovroirh.jpg

http://i243.photobucket.com/albums/ff276/armenk2000/Misc/spoiler4_zps6k3ith4h.jpg

http://i243.photobucket.com/albums/ff276/armenk2000/Misc/spoiler2_zpsww3bcumo.jpg

http://i243.photobucket.com/albums/ff276/armenk2000/Misc/spoiler1_zpsnwizzacw.jpg

(Last pic - exterior black 'GT' panel does not have to be removed for the spoiler removal process. That's for another mod I'm working on)

Screw
08-29-2015, 12:07 PM
Looking like TMS tutorials , nice details now show us the mods ;)

Armen
08-29-2015, 04:34 PM
Ya, I just did it cause I couldn't find anything on the net. Obviously it's not complicated, but it would have been nice just to have a bit of info before I started ripping my new car apart, lol. Anyway, hopefully I'll have pics for next weekend. This coming week I install stuff. Have some stuff out for paint so hopefully everything comes together for next weekend.

TheMustangShow
08-29-2015, 04:38 PM
What wing is going on?

Gonna be the same height as that light bar thingy?

Armen
08-29-2015, 04:46 PM
What wing is going on?

Gonna be the same height as that light bar thingy?

Haha... Light bar 'thingy'... your favourite mod.

Something more aggressive to balance out the rest of the look I'm going for. Nothing crazy tho and nothing really unique already as far as 15MY mods go. But hopefully it helps to bring it altogether.

Ghost Rider
08-29-2015, 05:13 PM
nice write up...

*waits for install thread*